| X200 | 1- / 3-phase 200 V class | |
| Model number | 002 SFEF | 004 SFEF | 005 SFEF | 007 SFEF | 011 SFEF | 015 SFEF | 022 SFEF | |
| Applicable motor (kW) | 0.2 | 0.4 | 0.55 | 0.7 | 1.1 | 1.5 | 2.2 | |
| Rated output current (A) | 1.4 | 2.6 | 3.0 | 4.0 | 5.0 | 7.1 | 10.0 | |
| Rated input voltage | 1 ~ 200 … 240 V, +10 %, -15 %, 50/60 Hz ±5 % | |
| Rated output voltage | 3 ~ 200 … 240 V (corresponding to input voltage) | |
| Integrated EMC filter | EN61800-3 category C1 filter | |
| Output frequency range | 0.5 … 400 Hz | |
| Frequency accuracy (at 25 °C ±10 °C) | Analogue setting: ±0.4 %, digital setting: ±0.01 % | |
| Frequency setting resolution | Analogue setting: Maximum frequency/1000, digital setting: 0.1 Hz | |
| V/f characteristics | V/f control, V/f variable (constant torque, reduced torque) | |
| Overload capacity | 150 % for 60 s | |
| Acceleration/deceleration time | 0.01 - 3000 s (linear, sigmoid), two stage accel./decel. | |
| Starting torque | 100 % at 6 Hz | |
| Input | Intelligent input terminal | 10 kOhm input impedance, sink / source logic selectable | |
| Functions | FW(Forward), RV(Reverse), CF1-CF4(Multispeed command), JG(Jogging), DB(External DC braking), SET(Second motor constants setting), 2CH(Second accel./decel.), FRS(Free-run stop), EXT(External trip), USP(Unattended start protection), SFT(Software lock), AT(Analog input selection), RS(Reset), PTC(Thermistor input), STA(3-wire start), STP(3-wire stop), F/R(3-wire fwd./rev.), PID(PID On/Off), PIDC(PID reset), UP/DWN(Remote-controlled accel./decel.) , UDC(Remote-controlled data clearing), OPE(Operator control), ADD(ADD frequency enable), F-TM(force terminal mode), RDY(quick start enable),S-ST(Special-Set 2nd Motor Data),EMR, NO(Not selected) | |
| Output | Intelligent output terminal | 27V DC 50mA max open collector output, 1 terminals, 1c output 250V AC/30V DC 2.5A relay (AL0, AL1, AL2 terminals) | |
| Functions | RUN(run signal), FA1(Frequency arrival type 1 - constant speed), FA2(Frequency arrival type 2 - over-frequency), OL(overload advance notice signal), OD(Output deviation for PID control), AL(alarm signal), DC(Wire brake detect on analog input), FBV(PID Second Stage Output), NDC(ModBus Network Detection Signal), LOG(Logic Output Function), ODC(Option Card Detection Signal), LOC(Low load) | |
| Analogue output terminal | 0 … 10 V, analogue frequency monitor, analogue current monitor | |
| Serial port | RS485 (Modbus RTU) | |
| Standards | CE, UL, cUL, c-Tick | |
| Protection | Overcurrent, overvoltage, undervoltage, overload, overheat, ground fault protection at startup, input overvoltage, external trip, EEPROM error, CPU error, USP error, Termistor error, Driver error, Safety stop | |
| Environ-mental conditions | Temperature / humidity | -10 … +50 °C (carrier derating required for ambient temperature higher than 40 °C), no freezing / 20 … 90 % humidity (non condensing) | |
| Vibration / lnstallation | 5.9 m/s2 10…55 Hz / altitude 1000 m or less, indoors, no corrosive gases or dust | |
| Options | Remote operator, copy unit, cable for digital operator, reactor for improving power factor, noise filter, ProDrive Software | |
| Protection class | IP20 | |
| Weight kg (approx.) | 0.8 | 1.0 | 1.5 | 2.4 | 2.5 | 1.5 | 2.3 | |
| | 80 x 155 x 93 | 80 x 155 x 107 | 110 x 189 x 128 | 110 x 189 x 155 | |
| X200 | 3-phase 400 V class |
| Model number | 004 HFEF | 007 HFEF | 015 HFEF | 022 HFEF | 030 HFEF | 040 HFEF | 055 HFEF | 075 HFEF |
| Applicable motor (kW) | 0.4 | 0.7 | 1.5 | 2.2 | 3.0 | 4.0 | 5.5 | 7.5 |
| Rated output current (A) | 1.5 | 2.5 | 3.8 | 5.5 | 7.8 | 8.6 | 13 | 16 |
| Rated input voltage | 3 ~ 380 … 480 V, +10 %, -15 %, 50/60 Hz ±5 % |
| Rated output voltage | 3 ~ 380 … 480 V (corresponding to input voltage) |
| Integrated EMC filter | EN61800-3 category C2 filter |
| Output frequency range | 0.5 … 400 Hz |
| Frequency accuracy (at 25 °C ±10 °C) | Analogue setting: ±0.4 %, digital setting: ±0.01 % |
| Frequency setting resolution | Analogue setting: Maximum frequency/1000, digital setting: 0.1 Hz |
| V/f characteristics | V/f control, V/f variable (constant torque, reduced torque) |
| Overload capacity | 150 % for 60 s |
| Acceleration/deceleration time | 0.01 - 3000 s (linear, sigmoid), two stage accel./decel. |
| Starting torque | 100 % at 6 Hz |
| Input | Intelligent input terminal | 10 kOhm input impedance, sink / source logic selectable |
| Functions | FW(Forward), RV(Reverse), CF1-CF4(Multispeed command), JG(Jogging), DB(External DC braking), SET(Second motor constants setting), 2CH(Second accel./decel.), FRS(Free-run stop), EXT(External trip), USP(Unattended start protection), SFT(Software lock), AT(Analog input selection), RS(Reset), PTC(Thermistor input), STA(3-wire start), STP(3-wire stop), F/R(3-wire fwd./rev.), PID(PID On/Off), PIDC(PID reset), UP/DWN(Remote-controlled accel./decel.) , UDC(Remote-controlled data clearing), OPE(Operator control), ADD(ADD frequency enable), F-TM(force terminal mode), RDY(quick start enable),S-ST(Special-Set 2nd Motor Data),EMR(Safety stop), NO(Not selected) |
| Output | Intelligent output terminal | 27V DC 50mA max open collector output, 1 terminals, 1c output 250V AC/30V DC 2.5A relay (AL0, AL1, AL2 terminals) |
| Functions | RUN(run signal), FA1(Frequency arrival type 1 - constant speed), FA2(Frequency arrival type 2 - over-frequency), OL(overload advance notice signal), OD(Output deviation for PID control), AL(alarm signal), DC(Wire brake detect on analog input), FBV(PID Second Stage Output), NDC(ModBus Network Detection Signal), LOG(Logic Output Function), ODC(Option Card Detection Signal), LOC(Low load) |
| Analogue output terminal | 0 … 10 V, analogue frequency monitor, analogue current monitor |
| Serial port | RS485 (Modbus RTU) |
| Standards | CE, UL, cUL, c-Tick |
| Protection | Overcurrent, overvoltage, undervoltage, overload, overheat, ground fault protection at startup, input overvoltage, external trip, EEPROM error, CPU error, USP error, Termistor error, Driver error, Safety stop |
| Environ-mental conditions | Temperature / humidity | -10 … +50 °C (carrier derating required for ambient temperature higher than 40 °C), no freezing / 20 … 90 % humidity (non condensing) |
| Vibration / lnstallation | 5.9 m/s2 10…55 Hz / altitude 1000 m or less, indoors, no corrosive gases or dust |
| Options | Remote operator, copy unit, cable for digital operator, reactor for improving power factor, noise filter, ProDrive Software |
| Protection class | IP20 |
| Weight kg (approx.) | 1.5 | 2.3 | 2.4 | 5.5 | 5.7 |
| Dimensions W/H/D in mm | 110 x 189 x 128 | 110 x 189 x 155 | 180 x 250 x 163 |
| * Item specifications are preliminary and are subject to change without notice |
